Skip to content
WaterHeating.caby CANRO Heating & Cooling

Service

Hot water sooner at distant taps, designed honestly

Design and installation of hot-water recirculation for tanks and tankless units in Metro Vancouver: dedicated return line or crossover valve, pump selection (external or the built-in RXP-style pump), timers and controls, priced with the gas and electrical cost explained.

Gas storage tankElectric storage tankHeat-pump water heaterGas tanklessIndirect tank
Get a ballpark estimateCall 604-359-1081

Free written estimate

Free in-home estimates for water-heater replacements and installations, as published by CANRO. Source, checked September 7, 2026.

Where CANRO provides on-site service

On-site service is currently offered across Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, Maple Ridge, Pitt Meadows, White Rock, Tsawwassen; plus Anmore, Belcarra, Lions Bay, Bowen Island, Abbotsford with travel or ferry arrangements confirmed by phone. Everything else on this site is reference information you can use anywhere in Canada.

See all service areas

About this service

Recirculation shortens the wait at a distant tap by keeping hot water moving through a loop. It does not make hot water instant, and it adds gas or electrical use while it runs, which is why the design includes a timer or demand control rather than a pump that runs around the clock. Rinnai documents crossover-valve and dedicated-return configurations with their own filters and codes; Navien's platforms use an external pump or ComfortFlow-style setup.

The installation covers the pump, the return line or crossover valve, the control settings (including the parameter configuration tankless units need), insulation on the loop where it pays, and a walkthrough of the running schedule and the added operating cost.

What's included

  • Loop design: dedicated return or crossover valve
  • Pump selection and installation (external or built-in as the unit provides)
  • Control and timer configuration
  • Air purge, filter setup and leak check
  • Free written estimate

Not included

  • Rerouting of existing piping beyond the loop connection (quoted separately)

Process

How it works

  1. 01

    Measure the waits

    The distant taps and their pipe runs are measured.

  2. 02

    Design the loop

    Return line or crossover, pump and controls are specified.

  3. 03

    Install and set

    The loop is installed, purged and programmed to a schedule.

Why CANRO

4.9★

4.9 from 85+ Google reviews

As published by CANRO Heating & Cooling on canroheat.ca, checked September 7, 2026.

Technical Safety BC licensed gas contractor

Gas-fitting licence LGA0043870 and boiler licence LBP0046450, as published by CANRO.

Source: canroheat.ca

Serving Metro Vancouver since 1999

Founded by George in 1999, as stated on canroheat.ca. Boiler and hydronic expertise is CANRO's, not this domain's.

Source: canroheat.ca

Red Seal HVAC, WorkSafeBC and liability insured

As stated on canroheat.ca. Bonding and association memberships: not published.

Source: canroheat.ca

Frequently asked questions

Is hot water instant with recirculation?

No. It is quicker at the tap, not instant, and it adds operating cost while the loop runs. A timer or demand control limits both.

Can my tankless unit support recirculation?

Most condensing units can, with an external pump or a built-in pump model (such as Rinnai's RXP), configured per the manual, including crossover-valve mode with its bypass filter.

Get a ballpark estimate in two minutes

Answer a few questions for a CAD range before you share any contact details.

On-site service in Metro Vancouver, BC. Call to check availability.

Call 604-359-1081Start the estimate

Related services and help

Sources and verification

Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.

Call 604-359-1081Get Estimate